Skip to content

Tandem Solar Cells: The Next Generation of Solar Energy Technology

Tandem Solar Cells: The Next Generation of Solar Energy Technology
19/10/2026    662 Views

How can two materials stacked on top of each other get past a limit that has constrained silicon panels for decades? This is a simplified technical review of the idea, the numbers and the obstacles, and what all of it means for a country like Iraq. Key Points A single-junction silicon panel is approaching a theoretical ceiling that better manufacturing cannot break. A tandem cell places a perovskite layer on top of silicon, so the two layers share the solar spectrum. In the laboratory, these cells have exceeded the theoretical limit of a single junction, but they still face tests of lifetime, cost and large-scale manufacturing. Field testing under Iraq’s heat and dust is the missing link, and it is an open research opportunity. What if the panel on your roof converted only about a fifth of sunlight into electricity? At midday, roughly 1,000 watts of sunlight reach every square meter of the Earth’s surface. Yet a silicon panel on a house, school or factory roof turns only about a fifth of that energy into electricity. The rest is lost as heat or passes through the panel without being captured. A reader might assume the problem is manufacturing quality, but the truth runs deeper: a single silicon cell has a theoretical limit of around 29% that it cannot exceed, however well it is made. Tandem solar cells offer a different answer. Instead of searching for a better material, we stack two materials on top of each other. This article explains the idea simply, presents the latest figures and the remaining obstacles, and ends with a question that concerns us directly: how will this technology perform in our climate? 1. Where Does Solar Energy Get Lost? Sunlight is not one color but a broad spectrum, and each color carries a different amount of energy per “packet” of light (a photon). A semiconductor has an energy threshold called the bandgap. A photon with less energy than this threshold passes through the material, much as water passes through a wide-meshed net, and is wasted. A photon with much more energy is absorbed, but the excess turns into heat within moments instead of becoming electricity. In this sense, a single material is always a compromise. A low threshold captures many photons but wastes the energy of the blue ones, while a high threshold preserves photon energy but loses all the weaker photons. Silicon, with a bandgap of about 1.12 electron volts, sits in a good region but is not ideal for the whole spectrum. An analogy: imagine a single sieve trying to sort grains of different sizes. If its holes are wide, small grains pass through; if they are narrow, large grains are trapped together with the small ones. The smarter solution is two sieves in sequence, each with a suitable hole size. 2. The Theoretical Ceiling of a Single Cell In 1961, Shockley and Queisser showed that any single-junction solar cell has a maximum efficiency that depends on its bandgap. They estimated this limit at about 30% in their original paper, while modern calculations based on the standard solar spectrum (AM1.5) give about 33.7% at the best possible bandgap. For silicon specifically, the value falls to about 29.4% (Richter and colleagues calculated 29.43% in 2013) for additional reasons, chiefly the loss of charge carriers inside the material itself through a process called Auger recombination. The best laboratory silicon cells today are already close to this ceiling, so the remaining room for improvement is very small. The question is therefore no longer “how do we improve silicon?” but “how do we go beyond it?”, and the most widely accepted answer is stacking. The solution was not a better material, but a smarter idea: let two materials cooperate. 3. The Idea: Two Layers Sharing the Spectrum In a tandem cell, a layer of perovskite is placed on top of a silicon cell. The perovskite used here has a wider bandgap (about 1.6 to 1.8 electron volts), so it captures blue and green light efficiently and converts its energy into electricity with less heat loss. Red and infrared light passes through the top layer, because its energy is below that layer’s threshold, and reaches the silicon, which captures it. The spectrum is thus divided between the two layers, each working in the region it handles best. In numbers, using the approximate relationship between bandgap and wavelength (wavelength in nanometers ≈ 1240 ÷ energy in electron volts), the perovskite layer absorbs light with wavelengths shorter than about 740 nm, silicon absorbs from about 740 to 1107 nm, and light beyond that is not absorbed by either layer. 4. What Does Each Layer Do? Every layer in a tandem cell has a specific job. The metal grid and the transparent conductive layer collect current from the cell’s surface while letting light through. The electron transport and hole transport layers surround the perovskite and pull each type of charge in a different direction, so that electrons and holes do not recombine and waste energy. Between the two cells, the interconnecting layer acts as an electrical bridge joining the top cell to the bottom cell, and the same idea repeats with the silicon contacts and the rear electrode. An important engineering point follows: in the common two-terminal design, the two cells are connected in series, so the same current flows through both. The thickness and bandgap of the top layer must therefore be designed so that each cell generates a similar current. Otherwise the weaker current limits the performance of the whole cell. Engineers call this requirement current matching. 5. Connection Types and Material Combinations First: how the two cells are connected There are two main ways to connect the top and bottom cells, each with its own advantages and cost: Two-terminal (2T): The two cells are built together and connected in series with only two electrical terminals. Advantages: fewer layers, lower manufacturing cost, and a connection similar to a conventional panel. Drawbacks: it requires precise current matching and is affected by changes in the spectrum during the day. Four-terminal (4T): Two independent cells stacked on one another, each with its own pair of terminals. Advantages: no need for current matching, and each cell can be optimized separately. Drawbacks: it needs extra transparent conductive layers that absorb some light, and the wiring and encapsulation are more complex. Second: the materials used Perovskite/silicon is the most mature combination, but it is not the only one. Other combinations are being tested today for different applications: Perovskite/silicon: A wide-bandgap perovskite on top of a silicon cell. It is the closest to commercialization and benefits from the existing silicon industry. Perovskite/perovskite: A wide-bandgap perovskite on top of a narrow-bandgap perovskite. Suited to light and flexible panels, but the stability of the narrow-bandgap layer is a challenge. Perovskite/CIGS: A perovskite on top of a thin-film cell made of copper, indium, gallium and selenium. Suitable for flexible, lightweight applications, but still less efficient and more complex than the previous option. Triple-junction: Three layers that split the spectrum into three parts. Their theoretical ceiling is higher than that of double-junction cells, but so are their complexity and cost. 6. Numbers That Change the Picture In July 2026, LONGi announced a perovskite/silicon tandem cell with an efficiency of 35.5%, measured and certified by the European Solar Test Installation (ESTI). Its previous figure was 34.85%, certified by the US National Renewable Energy Laboratory (NREL) in 2025. Both figures exceed the 33.7% theoretical limit of a single-junction cell. The speed is striking: silicon needed many decades to reach its current efficiencies, whereas perovskite has achieved comparable leaps in just a few years. The record progression: 2023: LONGi announced 31.8%, then 33.9%, the first time a tandem cell surpassed the single-junction theoretical limit. 2024: A record of about 34.6%, and in the same year Oxford PV recorded a residential-format panel with an efficiency of 26.9%. 2025: The figure rose to 34.85%, certified by NREL, and a large-area cell (about 261 cm²) with an efficiency of 33% was also announced. 2026: LONGi announced 35.5%, certified by ESTI, the highest announced value for this structure at the time of writing. The story has not stayed in the laboratory. Oxford PV runs a commercial production line for tandem cells in Germany, and in 2024 it recorded a residential-format 60-cell panel with an efficiency of 26.9%, certified by the Fraunhofer CalLab. Mainstream production today has TOPCon cells at about 25–26% at the cell level. In 2026, LONGi also announced tandem modules with efficiencies of 31.4% and 29.4% that were listed in efficiency tables, which means Oxford PV’s figure is no longer the highest for modules. It is worth noting honestly that LONGi itself stated in mid-2026 that it has no active plan for mass production of these cells, and that the record result remains at the research stage. For a general comparison: the theoretical limit for a single silicon cell is about 29.4%, TOPCon cells in current production reach about 25–26%, Oxford PV’s tandem panel reaches 26.9%, and the record tandem cell reaches 35.5%. Note that some of these figures are for cells and others for complete panels, so the comparison is for general illustration and not between exactly equivalent values, since the efficiency of a complete panel is usually lower than that of a single cell. 7. Why Don’t We See Them on Every Roof Yet? Because the road from the laboratory to the rooftop is long. The main obstacles: Operating lifetime: Perovskite is sensitive to moisture, heat and radiation, and needs tight encapsulation to last 25 years the way a silicon panel does. In addition, wide-bandgap compounds can suffer from “halide segregation” under continuous illumination, which changes their absorbing color and gradually reduces efficiency. Large-scale manufacturing: Moving from a cell the size of a fingernail to a panel of one square meter while keeping efficiency is still a real engineering challenge, especially given the textured silicon surface on which the top layer is coated. Materials and environment: The most efficient perovskite compounds contain lead, which calls for attention to environmental safety, safe encapsulation and end-of-life recycling. Cost: It is not enough for a panel to be more efficient; the cost per kilowatt-hour must ultimately be lower, and that depends on mass production and on the panel’s actual lifetime. Standards and certification: Investors and banks need long-term lifetime data and standardized certifications before they finance a large project with a new technology. 8. What Does This Mean for Iraq? Our country is among the richest regions in the world in solar radiation, but also among the harshest in heat and dust. These two traits strongly shape the performance of any panel: efficiency falls as cell temperature rises, and dust blocks part of the light. For this reason, any new technology needs local field testing before it is relied upon, since the performance of panels in the summer of the middle Euphrates and the south is not like their performance in European laboratories. This is an open research area for our centers and universities: to measure, compare and verify for ourselves. On the other hand, the higher a panel’s efficiency, the less area is needed to produce the same power, which matters for the limited roof space of homes, schools and institutions. Open research questions: How does current matching behave in two-terminal cells when the spectrum changes between morning, midday and sunset in dusty air? What effect do temperatures above 50 °C have on the lifetime of the perovskite layer and on the efficiency of the whole cell? Which types of encapsulation best resist dust, seasonal humidity and heat together? How does the cost per kilowatt-hour of a tandem panel compare with that of a high-efficiency silicon panel under Iraqi operating conditions? 9. Conclusion and Outlook Silicon panels will not disappear tomorrow; they remain the industrial and economic foundation of solar energy worldwide. But the direction is clear: the next generation will be tandem, and whoever understands this technology today will be ready to lead the clean energy market tomorrow. Research is heading along three tracks: extending operating lifetime through better encapsulation and more stable materials, carrying record efficiencies from small cells to full panels, and trying triple-junction structures that theoretically approach much higher efficiencies. The question we leave to our students and researchers: how will these panels perform under the heat and dust of an Iraqi summer? 10. Glossary Bandgap: The minimum energy a photon needs to free an electron in a semiconductor. Photon: A single packet of light; its energy depends on the color of the light. Shockley–Queisser limit: The maximum theoretical efficiency of a single-junction solar cell. Perovskite: A family of crystalline materials used as a light-absorbing layer, notable for having a tunable bandgap. Two-terminal (2T): A tandem cell with two electrical terminals, whose layers are connected in series. Current matching: The closeness of the current generated by each layer in a two-terminal cell. References NREL, Best Research-Cell Efficiency Chart. Shockley, W. & Queisser, H. J. (1961). Detailed balance limit of efficiency of p-n junction solar cells. Journal of Applied Physics, 32(3), 510–519. DOI: 10.1063/1.1736034. Richter, A., Hermle, M. & Glunz, S. W. (2013). Reassessment of the limiting efficiency for crystalline silicon solar cells. IEEE Journal of Photovoltaics, 3(4), 1184–1191. DOI: 10.1109/JPHOTOV.2013.2270351. LONGi Green Energy, announcements on perovskite–silicon tandem efficiency (2023–2026); pv magazine, July 2026. Oxford PV, press release “Oxford PV debuts residential solar module with record-setting 26.9% efficiency”, 19 June 2024 (certified by Fraunhofer CalLab). China Photovoltaic Industry Association (CPIA), 2025–2026 roadmap, for average TOPCon cell efficiencies. About the author: Israa Mohammed Hassan is an MSc student in Renewable Energy Engineering and works at the Al-Mustaqbal Energy Research Center, Al-Mustaqbal University, Hillah, Iraq.

Tags
#Education #Seminar #Conference #Research